想一睹软管泵路沿石成型机产品实拍产品的真实风采吗？我们的现场实拍视频将带您亲临现场，感受产品的卓越品质和创新设计，不容错过！
以下是:安徽宣城软管泵路沿石成型机产品实拍的图文介绍
软管泵工作原理：
一根内壁光滑，强度可靠的特制橡胶软管安装在泵体内部，通过一对压辊沿着软管旋转挤压，这样的 旋转使得介质往一个方向输送而不会倒流，软管在输送介质之后，由被压扁软管的自身弹性和侧导轮的强制下，软管恢复原状，此时，软管内产生高真空将介质再次吸入管腔，然后介质在随之而来的压辊挤压下从软管内排出，如此周而复始，介质不断的被吸入和排出。目前产品使用温度为≤100℃。根据用户需要可以开发使用温度在120℃的软管泵软管产品。
Working principle of hose pump:
A special rubber hose with a smooth inner wall and reliable strength is installed inside the pump body. It is rotated and squeezed along the hose by a pair of pressure rollers. This rotation allows the medium to be transported in one direction without flowing back. After that, due to the elasticity of the flattened hose and the force of the side guide wheels, the hose returns to its original state. At this time, a high vacuum is generated in the hose to suck the medium into the lumen again, and then the medium is pressed by the subsequent pressure roller. It is discharged from the hose under the squeeze, and so on and on, the medium is continuously sucked in and discharged. The current product temperature is ≤100 ℃. According to user needs, we can develop hose pump hose products with a temperature of 120 ℃.
一根内壁光滑，强度可靠的特制橡胶软管安装在泵体内部，通过一对压辊沿着软管旋转挤压，这样的 旋转使得介质往一个方向输送而不会倒流，软管在输送介质之后，由被压扁软管的自身弹性和侧导轮的强制下，软管恢复原状，此时，软管内产生高真空将介质再次吸入管腔，然后介质在随之而来的压辊挤压下从软管内排出，如此周而复始，介质不断的被吸入和排出。目前产品使用温度为≤100℃。根据用户需要可以开发使用温度在120℃的软管泵软管产品。
Working principle of hose pump:
A special rubber hose with a smooth inner wall and reliable strength is installed inside the pump body. It is rotated and squeezed along the hose by a pair of pressure rollers. This rotation allows the medium to be transported in one direction without flowing back. After that, due to the elasticity of the flattened hose and the force of the side guide wheels, the hose returns to its original state. At this time, a high vacuum is generated in the hose to suck the medium into the lumen again, and then the medium is pressed by the subsequent pressure roller. It is discharged from the hose under the squeeze, and so on and on, the medium is continuously sucked in and discharged. The current product temperature is ≤100 ℃. According to user needs, we can develop hose pump hose products with a temperature of 120 ℃.
软管泵压辊的调整
泵出厂时，压辊已按正常情况调整到位，如遇物料吸不上，或在泵的额定压力下，口量达不到要求，请调整压辊的偏心距，其步骤如下：
（1）先将泵壳两侧相应的圆孔有机玻璃盖板与泵出口端的长方形有机玻璃盖板打开，将转子压辊旋转至两圆孔之间，其螺栓正对圆孔，然后用套筒扳手将两端螺栓拧松，再用小圆棒或十字螺丝刀，对准标有0，1，2，3的圆孔，拨动压辊一侧内的偏心套转动，偏心套的数字越大，其压辊与泵壳间的距离越小，软管压的越紧，其调整是以转子的顶端的刻线为基准，数字越大，压的越紧，反之亦然。
（2）调整间隙时一定要注意不要压的过紧，以达到流量为准，压的越紧，对胶管的寿命影响越大。
泵出厂时，压辊已按正常情况调整到位，如遇物料吸不上，或在泵的额定压力下，口量达不到要求，请调整压辊的偏心距，其步骤如下：
（1）先将泵壳两侧相应的圆孔有机玻璃盖板与泵出口端的长方形有机玻璃盖板打开，将转子压辊旋转至两圆孔之间，其螺栓正对圆孔，然后用套筒扳手将两端螺栓拧松，再用小圆棒或十字螺丝刀，对准标有0，1，2，3的圆孔，拨动压辊一侧内的偏心套转动，偏心套的数字越大，其压辊与泵壳间的距离越小，软管压的越紧，其调整是以转子的顶端的刻线为基准，数字越大，压的越紧，反之亦然。
（2）调整间隙时一定要注意不要压的过紧，以达到流量为准，压的越紧，对胶管的寿命影响越大。
展望未来，豫信致诚机械设备(宣城市分公司)不是一味的追求什么规模，而是生产出优质 柴油滑模机、渠道注浆泵、纸浆成型机、型材成型机、高压成型机、水泥发泡成型机产品，为客户服务，让客户心中永远记得有这样一个重质量，守诚信的单位，永远存在于广大客户的心中。
